Request
https://api.motor.com/v1/Information/Vehicles/Attributes/{AttributeType}/{AttributeID}/Content/Details/Of/ServiceProcedures/{ApplicationID}
Check Our Documentation
Example From Selectline
Response
[xml]
<MWSInformationContentRs xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<Body>
<Attributes>
<Countries>
<VehicleCountry>
<Code>USA</Code>
<CountryID>1</CountryID>
<Name>United States</Name>
</VehicleCountry>
</Countries>
<Engines>
<EngineInfo>
<Aspiration>Naturally Aspirated</Aspiration>
<BlockType>L</BlockType>
<CID>-</CID>
<CylinderCC>1799</CylinderCC>
<CylinderHeadType>SOHC</CylinderHeadType>
<CylinderLiter>1.8</CylinderLiter>
<Cylinders>4</Cylinders>
<Designation>R18A1</Designation>
<EngineBoreInch>3.19</EngineBoreInch>
<EngineBoreMetric>81.0</EngineBoreMetric>
<EngineID>2913</EngineID>
<EngineStrokeInch>3.44</EngineStrokeInch>
<EngineStrokeMetric>87.3</EngineStrokeMetric>
<EngineVIN>-</EngineVIN>
<FuelDeliveryInfo>
<ControlType>Electronic</ControlType>
<FuelDeliveryID>65</FuelDeliveryID>
<SubType>MFI</SubType>
<SystemDesign>PGM-FI</SystemDesign>
<Type>FI</Type>
</FuelDeliveryInfo>
<FuelType>GAS</FuelType>
<HorsePower>U/K</HorsePower>
<IgnitionSystem>Distributorless</IgnitionSystem>
<KilowattPower>U/K</KilowattPower>
<Manufacturer>Honda</Manufacturer>
<ManufacturerType>OE</ManufacturerType>
<Valves>16</Valves>
<Version>i-VTEC</Version>
<Description>1.8L L4 (R18A1) GAS FI</Description>
</EngineInfo>
</Engines>
<SubModels>
<VehicleSubModel>
<SubModelID>699</SubModelID>
<SubModelName>DX</SubModelName>
</VehicleSubModel>
</SubModels>
</Attributes>
<ServiceProcedures>
<ServiceProcedureApp>
<ApplicationID>106180953</ApplicationID>
<Category>
<ID>4</ID>
<ProductType>Service</ProductType>
<Product>Service Procedures</Product>
<Article>Component Replacement</Article>
</Category>
<Taxonomy>
<Action>R&R</Action>
<CommonName />
<GroupID>2</GroupID>
<GroupName>Air Conditioning System</GroupName>
<LiteralName>Air Conditioning Compressor R&R</LiteralName>
<SubGroupID>51</SubGroupID>
<SubGroupName>Compressor</SubGroupName>
<SystemID>4</SystemID>
<SystemName>HVAC</SystemName>
<TaxonomyID>11194</TaxonomyID>
<InfoObject>
<Description>Compressor</Description>
<InfoObjectID>58</InfoObjectID>
</InfoObject>
</Taxonomy>
<AttributeMappings>
<MappedAttribute>
<ID>699</ID>
<Type>SM</Type>
</MappedAttribute>
<MappedAttribute>
<ID>1</ID>
<Type>CO</Type>
</MappedAttribute>
<MappedAttribute>
<ID>2913</ID>
<Type>EN</Type>
</MappedAttribute>
</AttributeMappings>
<Qualifiers />
<Links>
<Link>
<Href>/Information/Vehicles/Attributes/basevehicleid/22124/Content/Details/Of/ServiceProcedures/106180953/4</Href>
<Rel>Self</Rel>
</Link>
</Links>
<Items>
<ServiceProcedure>
<ProcedureID>156430</ProcedureID>
<Data><MOTOR_Procedure><pstepgrp><p>Exploded view of compressor, <emph type="bold">Fig. <xref idref="ach1200000000846" />.</emph></p><stepgrp><step>If compressor is marginally operable, run engine at idle speed and let air conditioning work for a few minutes, then shut engine off.</step><step>Evacuate system as outlined under <emph type="dquote">Refrigerant Recovery</emph> in <emph type="dquote">General Service</emph> on main menu selection.</step><step>Remove fasteners on front inner fender from both wheel wells.</step><step>Remove front grill cover clips by carefully pulling up, then the cover by releasing front edge of cover from grill.</step><step>Remove drive belt.</step><step>Disconnect alternator connector and positive alternator cable from alternator.</step><step>Remove harness connector and harness clamps.</step><step>Remove two bolts holding alternator, then remove alternator.</step><step>Disconnect connector from A/C condenser fan motor. Detach wire harness clip. Remove upper mounting bolts, and A/C condenser fan shroud. Be careful not to damage radiator fins when removing A/C condenser fan shroud.</step><step>Remove bolt and nut, then disconnect suction hose and discharge hose from A/C compressor. Plug or cap lines immediately after disconnecting them to avoid moisture and dust contamination.</step><step>Remove mounting bolts and A/C compressor. Be careful not to damage radiator fins when removing A/C compressor.</step><step>Reverse procedure to install, noting the following:</step><stepgrp2><step><emph type="bold">Torque</emph> compressor mounting bolts to 16 ft. lbs.</step><step><emph type="bold">Torque</emph> suction and discharge line nuts to 86 inch lbs.</step><step>Replace O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use correct O-rings for R-134a to avoid leakage.</step><step><emph type="bold">Torque</emph> alternator mounting bolts to 17 ft. lbs.</step><step>Recharge A/C refrigerant as outlined under <emph type="dquote">Charging System</emph> in <emph type="dquote">General Service</emph> on the main menu selection.</step></stepgrp2></stepgrp></pstepgrp></MOTOR_Procedure></Data>
<ReferenceSet>
<Documents>
<ServiceProcedureContentDocument>
<Caption />
<DocumentID>2429705</DocumentID>
<Format>image/gif</Format>
<Links>
<Link>
<Href>/Information/Vehicles/Attributes/basevehicleid/22124/Content/Documents/Of/ServiceProcedures/2429705</Href>
<Rel>ServiceProceduresDocument</Rel>
</Link>
</Links>
<Name>ACH1200000000846</Name>
<Sequence>1</Sequence>
<Type />
<AnchorDocumentID>2429705</AnchorDocumentID>
</ServiceProcedureContentDocument>
</Documents>
</ReferenceSet>
<Schema>MOTOR_Procedure</Schema>
<Sequence>9</Sequence>
</ServiceProcedure>
</Items>
</ServiceProcedureApp>
</ServiceProcedures>
</Body>
<Header>
<Date>Thu, 30 Apr 2015 19:20:43 GMT</Date>
<Messages />
<Status>OK</Status>
<StatusCode>200</StatusCode>
</Header>
</MWSInformationContentRs>
[/xml]